| An assortment of thread lockers, retaining compounds and
gasket eliminator in convenient and economical dispensers. For years, we
have had requests for such an assortment. Each of these is within arms
length of any properly equipped Rotax Technician. Don't run out.
Seven 5 ML syringes with Velcro® hangers. Loctite® products included in this kit are: Only $36.95 BUY NOW
|
 |
Please Click Here for hints on useage and storage of these bulk repackaged products
| 222 Violet, Low Strength Thread Locker.
For
1/4" diameter and smaller fasteners. Where "Thread Locker" is specified
in Rotax documentation, that spec is generally European version 221 Violet.
222 is the correct US equivalent
LT222X5 5 ml only $6.99 |
242 Blue, Thread Locker. For
larger fasteners. Can be removed with normal tools, without heating. This
is the most commonly used Thread Locker in most industries
LT242X5 5 ml only $6.99 |
| 271 Red, High Strength Thread Locker.
Requires
heat for removal. 271 is specified in many application on various machines
and equipment, but NOT on Rotax Engines. We do, however use 271 for one
particular application on LQ Rotax engines, plus "other" shop uses make
271 a necessary part of our Loctite Products Kit. ...Use it judiciously.
LT271X5 5 ml only $6.99 |
290 Green, Thread Locker. A
low viscosity
(numerically) penetrating Thread
Locker which has an amazing ability to wick into fasteners already assembled.
This first got our attention when we saw it used for an effective field
repair on a riveted aluminum fuel tank. No "specified" use on Rotax, but
with one use, it will become a "must have" in any shop.
LT290X5 5 ml only $6.99 |
| 515 Gasket Eliminator. For
sealing the mating surfaces on crankcases. THIS is used on Rotax engines
at the manufacturing level. 518 and 574 can be adequately substituted.
574 comes with an impressive (expensive) applicator.
515 or 518 will need to be "smeared around by finger" method. It is speculated, that because there is no direct German to English translation for "smeared around by finger", that Rotax specifies 574 in their manual. LT515X5 5 ml only $5.99 |
609 Green, Cylindrical Part Bonding Compound.
This
is a low viscosity (numerically)
Retaining
Compound for bonding bearings to shafts and similar close fit components.
We use this to bond: Condensers on Point Ignition Rotax engines, electric
start ring gear mating surfaces, etc. The flow characteristic of 609 can
make it a desirable alternative to the more viscous 648
LT609X5 5 ml only $6.99 |
| 648 Green, Cylindrical
Part Bonding Compound. Higher viscosity (numerically)
and strength than 609. Loctite 648 is specified by Rotax in man648 Green,
Cylindrical Part Bonding Compound. Higher viscosity and strength
than 609. Loctite 648 is specified by Rotax in many areas of assembly on
Rotax engines and Gear Boxes. This, historically has been difficult to
locate, in the USA and substitutions have often been used. Green Sky, has
now sourced 648 and packaged it for convenient use in our LT-7 kit.
LT648X5 5 ml only $8.99 |
Technical Data Sheets for these Loctite® Products http://www.loctite.com/datasheets/tds/Product_290.pdf http://www.loctite.com/datasheets/tds/Product_242.pdf http://www.loctite.com/datasheets/tds/Product_271.pdf http://www.loctite.com/datasheets/tds/Product_290.pdf http://www.loctite.com/datasheets/tds/Product_515.pdf http://www.loctite.com/datasheets/tds/Product_609.pdf http://www.loctite.com/datasheets/tds/Product_648.pdf |